Construction – Page 2

HAM-gadget (5) – menu structure

Posted on2021-11-072021-11-08

This weekend I built in a menu structure into the HAM-gadget. Also I created a possibility to store and retrieve settings to the ATMEGA328P’s EEPROM, so they are saved for the next time you switch on the device. For now, you have to retrieve them manually, but that’s quicker then… Read the rest

HAM-gadget (3) – connected the GPS

Posted on2021-10-242021-10-24

Finally got it to work After much fiddling and trying out different libraries I finally had a bright moment and reverted back to the library that has been specifically made for this GPS module by Velleman… Duh… prototype, software version 0.5 That worked, also after some tweaking of the wires… Read the rest

HAM-gadget (2) – new Arduino board

Posted on2021-10-232021-10-23

Arduino board left and center, GPS module on the right, GPS antenna on top Today some new stuff arrived. First of all the new Arduino RP2040 Connect board, a Wifi capable board with a much smaller form factor then the Uno clone I had before. Second came in the GPS… Read the rest

HAM-gadget (1) – building a shack gadget

Posted on2021-10-222021-10-23

Today I worked on version 0.1 of my new project. It’s in the prototype stage as you can see in the picture below. For this test it’s an Arduino Uno (clone by Velleman), two DS18B20 temperature sensors and two 20 x 4 displays. This version is for setting up the… Read the rest

Antenna preparation – masts and result

Posted on2021-05-152021-06-06

My son in law is a crane operator and he was kind enough te lend me a hand in erecting the masts for the antennas. First, we set up the big mast (a long piece of scaffolding pipe attached to two mounts that are bolted into the wall. Jig My… Read the rest

Antenna preparation – the antennas

Posted on2021-05-142021-05-16

After preparing the cables, next up are the antennas themselves. I have two at the moment: a Diamond Discone (25MHz – 1300 MHz) and a HyEndFed 3 band antenna (10, 20 and 40 meter). The coax plugs have to be weather proofed with vulcanizing tape. Diamond DisconeHyEndFed MK IIIPlug and… Read the rest

Antenna preparation – cables and plugs

Posted on2021-05-132021-05-16

A lot of work goes into getting antennas up and running. First, we have to solder plugs onto the end of our coax cables.… Read the rest

Antenna preparation

Posted on2021-05-082021-05-08

Today, my son in law brought me a piece of 7 meter (21 feet) scaffolding pipe. Together we mounted two brackets to the wall of the house. The brackets need to extend 0,5 meter to allow the mast to go past the gutter. Scaffolding pipe on the deck on top… Read the rest

HAM shack

Posted on2021-05-052021-05-05

Made a little riser so the Power Supply Units could have a spot below the radio’s. Nice huh?… Read the rest

Bench hooks preview

Posted on2019-12-08

I’m creating some bench hooks for my workbench. More details to follow, but I thought I’d give you a sneak preview…… Read the rest

Workbench, finally done!

Posted on2019-11-09

This afternoon, I finally could put the workbench on its feet (wheels). Here it is, in my workshop: I am one happy woodworker! Other side, bench vise on the left Second vise on the right, with spring-clamps… Read the rest

Workbench cross beam

Posted on2019-11-09

To reinforce the wheel sets some more, I mounted a cross beam over the lowest parts of the wheel sets.… Read the rest

Workbench wheelset reinforcement

Posted on2019-11-09

Today I reinforced the wheelsets for my workbench. Two small pieces of 12mm plywood to make them a little more sturdy. Wheelsets reinforced Next and last will be a cross beam between the two wheelsets.… Read the rest

Workbench reinforcement

Posted on2019-11-08

This time I decided to reinforce the workbench before I put it on its feet (wheels). First I attached sheets of 12mm plywood to the back and the sides to prevent the parallelogram distortion that wrecked it last time. Back sideleft sideright side Next I will reinforce the wheel assemblies…… Read the rest

Workbench again

Posted on2019-11-062019-11-06

Due to the breakdown the first time, I had to re-assemble the under frame. After scraping of the old glue and sanding it down to the wood, I re-assembled one wheel set. Since I do not have large enough clamps, I used a ‘jijnblok’ to press them together. (‘jijnblok’ is… Read the rest